To complete a simple earring, the loop in the bead dangle is connected to the loop at the end of an ear wire finding leaving a completed earring.įour tools are essential and several other tools are useful in the construction of wire wrapped jewelry. The resulting bead hanging from a loop is called a "bead dangle". This wire is bent into a loop using hand tools and the excess wire is cut off. The portion of the head pin coming out of the opposite side of the bead is essentially wire. The bead is held in place by the "head" on the head pin. In the simplest example of handmade wire wrapped jewelry, a bead is threaded onto a jewelry making finding called a head–pin. A connection between two wrapped loops must be performed before the second loop is wrapped closed. A stronger (and better looking) loop is the closed loop, where the end of the wire is wrapped around the stem of the loop three or four times, so that the loop is permanent and cannot be opened, this is called a "wrapped loop". This means that the loop can be opened mechanically to allow it to connect to another component, which allows it to open too easily when strained. The best-looking loop is the eye loop, with a full circle of wire centered over the stem of wire (like a lollipop). A "P" loop is made by bending the wire until it touches the wire again (but this is too crude looking for serious jewelry use). Loops are connected to one another to make the mechanical connections between components. A mechanical connection is connecting a loop to another loop by interlocking them.Ī key element in wire wrapped jewelry is a loop made in wire. Wire wrapped jewelry is made using mechanical connections between components and without soldering or other heat treatments.Wire wrapped jewelry is made of wire and sometimes findings similar to wire (head-pins, jump rings, etc.).The key differences between making jewelry by wire wrapping and other approaches to making jewelry are two-fold Wire wrapped jewelry is jewelry made of wire with mechanical connections instead of soldered connections. The wire wrapping approach to making jewelry is primarily employed by individuals.īracelet close up, showing eight wrapped loops Characteristics Wire wrapping techniques are not frequently used for mass-produced jewelry because machines can cast (mold) jewelry components faster, more cheaply, and more precisely. Later, as the technique for soldering developed, the wire wrapping approach continued because it was an economical and quick way to make jewelry components out of wire. In the manufacture of this early jewelry the techniques for soldering did not exist. This Roman jewelry is dated to approximately 2,000 years ago. Other samples of jewelry from Ancient Rome show wire wrapped loops (one of the important techniques in making wire wrapped jewelry). This jewelry is dated at approximately 2000 BC. The British Museum has samples of jewelry from the Sumerian Dynasty, found in the cemetery of Ur that contain spiraled wire components. The technique of wrapping wire around itself gives this craft its name of wire wrapping.Įxamples of wire and beaded jewelry made using wire wrapping techniques date back to thousands of years BC. This makes the loop or decorative shape permanent. Frequently, in this approach, a wire is bent into a loop or other decorative shape and then the wire is wrapped around itself to finish the wire component. Wire components are then connected to one another using mechanical techniques with no soldering or heating of the wire. This technique is done with jewelry wire and findings similar to wire (for example, head-pins) to make components. Wire wrapping is one of the oldest techniques for making handmade jewelry. ( July 2013) ( Learn how and when to remove this template message) Please help to improve this article by introducing more precise citations. WHERE ( tC.actif = 1 AND EN = 1 ) AND tC.id_masterGamme_LAVAL = :id_masterGamme_LAVAL AND tC.id_masterFamille_LAVAL = :id_masterFamille_LAVAL GROUP BY tC.id_masterPrix ) GROUP BY tC.This article includes a list of references, related reading, or external links, but its sources remain unclear because it lacks inline citations. INNER JOIN trieurCollection tC ON mPrix.id_masterPrix = tC.id_masterPrix INNER JOIN prix_EN mPrixLang USING(id_masterPrix) WHERE tC.actif = 1 AND tC.EN = 1 AND tC.id_masterTrieurParent NOT IN (9,15) AND tC.id_masterGamme_LAVAL = :id_masterGamme_LAVAL AND tC.id_masterFamille_LAVAL = :id_masterFamille_LAVAL AND tC.reference IN ( SELECT mPrix.reference FROM masterPrix mPrix
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |